Blackberry Curve 8520 headset activated mode solution

Here's a solution for blackberry curve 8520 that the headset shows or in activated mode when making a call or someone calling the unto the device.

If trying to fix this problem do this some simple steps below:

1. Try to upgrade or update the blackberry 8520 firmware.

2. Pull the battery out and reinsert it back again in a few seconds.

If the above doesn't' work, you may then proceed to hardware troubleshooting.

The solution below shows a certain components that needs to be check.

Fix Blackberry bold 9000 NO Power solution

Here's a repair solution on how to fix blackberry bold 9000 unable to power up ( No -Power ).

In this guide it shows that the cause or having a faulty component is the Power Management IC, the PMIC is the one that controls and feeds power supply voltage to all other components from the battery source., Therefore, if the PMIC is damaged the device will totally paralyze (dead set )

. The main key solution for this problem is to rework, change or replace the PMIC. You can found this in other non working blackberry bold PCB board, just make sure that the said IC is still working
 



 

Nokia 6120c No Signal Solution

Simple guide for MX-KEY Blackberry Unlocking

* Read IMEI + MEP Code from your Blackberry

* Download and install the latest version of Blackberry Desktop Software or drivers from
Driver
* Connect the Blackberry phone to computer using the original USB


cable and start the Blackberry Logger and click Read Blackberry

Handset Info

* IMEI - this is the serial number of the phone

* MEP - this is the MEP name from where your phone is lockedSupported MEP

* for Unlock

* Supported MEP for MX-KEY:
Code:

MEP-12579-001


MEP-11139-001

MEP-06424-001

MEP-11139-004

MEP-11139-006

MEP-11139-003

MEP-11139-002

MEP-04104-003

MEP-11139-005

MEP-05277-001

MEP-14260-001

MEP-06899-001

MEP-06814-002

MEP-06893-001

MEP-04598-004

MEP-10129-001

MEP-06811-003

MEP-06810-002

MEP-06530-002

MEP-06530-001

MEP-06813-001

MEP-12579-002

MEP-07705-002

MEP-06259-002

MEP-08318-001

MEP-08395-001

MEP-13988-001

MEP-09004-001

MEP-08448-001

MEP-12186-001

MEP-13928-001

MEP-06041-003

MEP-06068-001

MEP-06041-001

MEP-07484-002

MEP-08209-002

MEP-09747-001

MEP-04104-005

MEP-07722-003

MEP-04546-001

MEP-07722-001

MEP-04938-002

MEP-04938-001

MEP-09783-002

MEP-09821-001

MEP-07722-002

MEP-07484-001

MEP-06849-001

MEP-06529-001

MEP-06529-002

MEP-04103-001

MEP-11246-001

MEP-14150-001

MEP-06813-002

MEP-15326-001

MEP-15326-002

MEP-14074-001

MEP-10073-001

MEP-06812-003

MEP-06899-002

MEP-08918-001

MEP-11016-001

MEP-12978-001

MEP-12622-002

MEP-11414-002

MEP-10129-002

MEP-06814-004

MEP-06814-001

MEP-13188-001

MEP-13710-001

MEP-11414-001

MEP-06423-001

MEP-04598-005

MEP-11534-002

MEP-06259-003

MEP-08209-001

MEP-07754-001

MEP-09938-001

MEP-06068-002

MEP-06424-002

MEP-09293-001

MEP-08448-002

MEP-10129-003

MEP-08881-001

MEP-08882-001

MEP-15343-001

MEP-07321-002

MEP-09690-001

MEP-11534-004

MEP-14052-001

MEP-09149-001

MEP-12209-003

MEP-07484-003

MEP-06041-006

MEP-12209-004

MEP-09667-001

MEP-04103-002

MEP-07484-004

MEP-14896-001

MEP-09783-003

MEP-04626-001

MEP-12599-003

MEP-06041-005

MEP-07723-001

MEP-14260-002

MEP-04104-006

MEP-12565-001

MEP-04626-002

MEP-15159-001

MEP-05277-004

MEP-12488-001

MEP-08589-001

MEP-09917-001

MEP-06849-002

MEP-16352-001

MEP-14896-002

MEP-09070-001

MEP-16472-001

MEP-04104-007

MEP-07705-003

MEP-05277-002

MEP-06812-001

MEP-04598-003

MEP-12980-002

MEP-12980-001

MEP-16419-001

MEP-16272-002

MEP-06041-007

MEP-04104-004

MEP-17232-001

MEP-13990-001

MEP-11534-005

MEP-14896-003

MEP-17490-001

MEP-16826-001

MEP-06041-008

MEP-11534-006

MEP-06041-004

MEP-07484-005

MEP-18637-001

MEP-10129-004

MEP-19322-003

MEP-11534-007

MEP-17568-002

MEP-07723-003

MEP-09625-001

MEP-04103-004

MEP-12907-002

MEP-20454-001

MEP-09292-002

MEP-07484-006

MEP-20099-002

MEP-14896-004

MEP-20669-001

MEP-13188-002

MEP-19877-001

MEP-08209-003

MEP-07484-007

MEP-15159-002

MEP-20099-004

MEP-21545-001

MEP-14896-005

MEP-20166-001

MEP-18601-001

MEP-13928-002

MEP-22793-001

MEP-14074-002

MEP-20099-009

MEP-23361-001

MEP-09821-002

MEP-11534-008

MEP-24124-001

MEP-13188-006

MEP-07723-004

MEP-24723-002

MEP-24723-001

MEP-10129-005

MEP-16272-003

MEP-24667-001

MEP-24660-001

MEP-12209-006

MEP-24409-002

MEP-13188-007

MEP-07723-005

MEP-12209-007

MEP-26594-001

MEP-14052-002

MEP-26900-003

MEP-05277-005

MEP-06041-009

MEP-13188-010

MEP-12209-008

MEP-27488-001

MEP-28364-001

MEP-16272-005

MEP-09292-003

MEP-28240-002

MEP-09292-001

MEP-28555-001

MEP-09292-004

MEP-13188-008

MEP-27501-003

MEP-14074-003

MEP-11246-002

MEP-29318-001
Then follow this steps:

MX-key BLACKBERRY Procedure:
* Connect the BB unit thru mini usb


* In connection click Blackberry then click connect

* Go to option double click blackberry tool

* Click scan

* Calculate code wait in seconds

* Enter IMEI + MEP CODE.

How to enter MEP codes in BlackBerry
* Insert any sim card


* Turn off all of the wireless connections

* Go to Options

* Select Advanced Options

* Select SIM Card

* Hit menu select show keyboard (where needed)

* Type MEPPD or MEPD (you will not be able to see the typed info)

* Enter MEP2 or MEPP2

* Now it will say enter network MEP code
Or this one:

Regarding Blackberry Unlock:
* Load Blackberry Desktop Manager From the blackberry website.


* Connect a fully turned on blackberry to the usb port.

* If prompted, dont enable mass storage mode.

* Let windows load the resp. drivers for the device.

* Fire up mobile.ex and select the blackberry from the connection list.

* Connect and run the blackberry applet from the modules.

* Scan for the device and it will give you the details of the device.

* Click calc code and the corresponding code will be shown in the display.
Now The Blackberry part:

* Put a locked sim card and turn on the phone.


* On the device go to options/advance options/sim

* It wont show anything here. (Blanck).

* Just type MEPD on the keypad.

* Some details will come on the screen.

* Again type MEP2 (remember to press alt key while pressing 2).

* It will ask u to enter the unlock code. Just enter the code

provided by the mxkey software. Remember u only have 10 chances to enter

the code correctly.

* It will say code accepted.

* Remove the battery put the simcard and restart and your handset is now unlocked.

Nokia 2323c Auto Off Solution

first flash your mobile if not trie this solution


take diode from 1100

Applications And Games For Iphone,Ipod touch And Ipad

Rugby Nations 2010 1.1.0 iPhone and iPod Touch



Description




“The only trophy we won this day, was the blood and sweat we left on the pitch.... and it was enough" - Anon



"The tactical difference between Association ******** and Rugby with its varieties seems to be that in the former, the ball is the missile, in the latter, men are the missiles." - Alfred E. Crawley (1913)



Rugby Nations is back with a vengeance bringing more beastly action from the game of gentlemen than ever before. Feel the temperatures rising as 12 international teams fight it out to become the champions of World’s greatest tournaments . This is your chance to lead your team of warriors to victory in the most grueling game of rugby union that has ever graced your iPhone/iPod Touch. The scrum is forming – are you in?



FULL-ON RUGBY ACTION AT YOUR FINGERTIPS

Immerse yourself into all aspects of the game from rucks and scrums to the killer drop-kicks. Three difficulty levels make sure that you don’t grow out of the game anytime soon.



SEE AND FEEL RUGBY AT IT’S PUREST FORM

Featuring impressive stadiums from around the world, gripping player graphics and intuitive controls – rugby never looked or felt this good!



TRULY GREAT TEAMS NEED GREAT LEADERS

Pick your country from the 12 finest teams in the world and lead your team to victory one pass at a time. Your team needs YOU.



CHALLENGE YOURSELF IN THE HARDEST RUGBY MATCHES OF ALL TIME

Collect your trophies from World Cup, Tri Nations or Six Nations or just get out there are score with ‘Play Now’.



RELIVE YOUR MOMENTS OF GLORY

With the replay feature, you can relive your finest moments.

-------------------------------------

WANT TO HEAR FIRST ABOUT NEW GAMES, EXCLUSIVE PROMOTIONS AND WIN STUFF?



FOLLOW US:twitter.com/distinctivegame



FIND US: facebook.com/distinctivegames



Promotions running weekly so come and join the fun!

CHECK OUT OUR EXCITING GAMES AVAILABLE NOW:



Dead Runner, Bonecruncher Soccer, Hockey Nations 2010, Heli Rescue and Pool Ninja



Free versions available: Dead Runner Free. Hockey Nations 2010 ShootOut and Bonecruncher Lite
Distinctive Developments Ltd Web SiteRugby Nations 2010 Support

What's New in Version 1.1.0

Retina Display Graphics

Multi-tasking

Improved Performance
Download

King Rupert 1.3 iPhone and iPod Touch

Description




This new action game will take you back to the medieval times when Kings and Wizards used to hang around in palaces doing their everyday things. Gameplay takes place in different parts of the kingdom, asks to complete various challenges, collect coins and much more! You will take control of King Rupert, who was cursed by the grumpy Wizard and needs your help. So, the only question is - Are you up for the challenge?



FEATURES

- Intuitive game controls;

- 3D graphics;

- Stunning visual game elements;

- Amazing story art;

- 30 unique levels;

- Physics based gameplay,

- Mining carts action;

- Puzzle elements;

- Collect coins to unlock new levels;

- Explosions!

- And much more!!!
What's New in Version 1.3

Faster story screens scroll;
Added swipe in levels selection pages;
Now game runs on earlier firmware versions (from 3.2);
Changed game icon (bug with LITE version icon);
Download

Iphone 3G LCD faint image display.JPG

I-phone 3GS Home Button Ways.jpg

V9 charging problem 100% solution

Here V9 solution for not charging or sometimes charging or sometimes no usb detect.

How To Repair Red Blink Sonyericsson K800i Using Setool

Symptoms :

1.Phone Is not powered on / dead


2.Phone only show red blinking ( charging led indicator ) when power key is pressed

3.Cannot read gdfs when ” identify ” on setool
Tools & Materials :
1.Setool Box with V1.01 or Latest software installed


2.Setool Cable set

3.K800i Gdfs file ( included on Setool folder )

4.K800i Erom file ( included on Setool folder )

5.Internet Connection
Step By Step :
1.Open Setool Software


2.Pick ” Empty Fill Repair ” Tab

3.Pick K800i Model

4.Pick ” Setting ” Tab

5.Check ” Signed Mode “

6.Back to ” Empty Fill Repair ” Tab

7.Click ” Recovery “, wait until process done

8.Add K800i Gdfs file

9.Add K800i Erom file ( pick CID 53 )

10.Connect phone to cable

11.Click ” Flash “

12.Wait until all process done

13.For last step, do Identify and confirm that gdfs is legiled.

14.All Done
Here’s the log operations :

First Identify


RUNNING v 1.01/UNI

CARD SERIAL 00xxxxxxx

USBFLASH DRIVER VERSION 02.02.00.05

CFG:000000000000

ChipID:9900,EMP protocol:0301

Speed:921600

FLASH ID: 897E

OTP: LOCKED:1 CID:51 PAF:1 IMEI:359xxxxxxxxxxxx CERT:N/A

FLASH CID:52 COLOR:RED

can’t get packet start.

packet not acknowledged (17)

setGDFS_params failed

failed to setup GDFS

Elapsed: 72 secs.
Repairing gdfs
RUNNING v 1.01/UNI


CARD SERIAL 00xxxxxxxxxx

USBFLASH DRIVER VERSION 02.02.00.05

SIGNED MODE (USING SERVER)

CFG:100000000000

RESET MODE STARTED

ChipID:9900,EMP protocol:0301

Speed:921600

RESET:070703 1106 NPACXC1250329_DB2020_CERTRESETLOADER_P3AA

FLASH ID: 897E

GOT SEED:034A77682380B07A15F00858

P96 AUTH PASSED

OTP: LOCKED:1 CID:51 PAF:1 IMEI:3590xxxxxxxxxxxx CERT:N/A

PHONE SUCCESSFULLY RESET TO DEVELOPER STATE

Elapsed: 26 secs.



SIGNED MODE (USING SERVER)

CFG:100000000000

ChipID:9900,EMP protocol:0301

Speed:921600

OTP: LOCKED:1 CID:51 PAF:1 IMEI:359xxxxxxxxxxxxxxxxx CERT:N/A

FLASH CID:49 COLOR:BROWN

LDR:060721 1021 DB2020_SERVICE_LOADER

FLASH ID: 897E

writing “D:Master FlasherSe tool 3v1.01gdfs_in_ssw_formatdb2020K800_GDFS_SSW.ssw”

CURRENT FLASH FILE CID:49

SSW uses full hash, hash len is: 640

Will flash 32 blocks…

writing “D:Master FlasherSe tool 3v1.01eromsdb2020DB2020EROM_CNV_RED52_BROWN_CID49_DB2020.ssw”

CURRENT FLASH FILE CID:49

SSW uses full hash, hash len is: 40

Will flash 2 blocks…

Setting up GDFS…

OTP WRITE NOT EXECUTED

WRITING CLEAR SIMLOCK UNITS…

ALL UNLOCK/LOCK CODES SET TO “75381610″

SIGNING…

Elapsed: 48 secs.
Identify after repair
CFG:000000000000


ChipID:9900,EMP protocol:0301

Speed:921600

FLASH ID: 897E

OTP: LOCKED:1 CID:51 PAF:1 IMEI:3590xxxxxxxxxxxxx CERT:N/A

FLASH CID:52 COLOR:RED



Model (from GDFS):K800i

Brand:Generic

MAPP CXC article: 2007-12-13 16:25 CXC1722434_TEMS

MAPP CXC version: R2B

Language Package: TEMS

CDA article: CDA12345678/123

CDA version: R2A

Default article: cxc1722435

Default version: R2B

PROVIDER: 000-00

SIMLOCKS NOT DETECTED



RESTORATION FILE NOT PRESENT

“2007-12-13_07-12-13 16:25 CXC1722434_TEMS”

YOU MUST PERFORM FULL FLASHING

WHEN “ALTERNATIVE SECURITY BYPASS” ENABLED

Nokia N97mini Some Solutions

Nokia N97 mini Earpiece Receiver Speaker Solution


Here's the Nokia N97mini Earpiece Speaker Solution that may possibly help fix if the receiver speaker does not have an audio signal output or No voice sound can be heard on it.


This problem may happens if the receiver speaker is already busted or the flex ribbon cable is already damaged. You may need to check these said components or parts first or try to replace with a new replacement spare

If both flex ribbon cable and the receiver speaker were okay and or already tried replacing it but the problem still exists. See the solution below for it shows the connection line paths and certain components of the earpiece speaker circuit on the main PCB board of Nokia N97 mini.



You may then trace each of the corresponding line paths and components where the said earpiece audio signal is being feeds. There are filter coil and an ESD protection chip is being used in the circuit, you may try to remove the ESD protection first then check or replace the filter coil.


If filter coil is okay and the ESD chip is already been remove and also ensuring that each corresponding connection line paths were okay; the next option will be by reworking the power management chip (GAZOO). Hope this may help solved your Nokia N97 earpiece speaker problem.

Nokia N97 mini Camera Hardware Failure Solution
Here's the Nokia N97 mini camera solution, this solution covers if there is one or both of the two camera doesn't work or unable to function.


If encountered camera failure on Noki N97 mini, you may first restore or update the device firmware. If the problem doesn't lie on the firmware, then try to replace the camera module and ensure that the flex ribbon cable is not damaged or already tried replacing it.

The solution below shows the location of particular components that holds for camera and may caused the problem if become faulty or damaged. You may then check these components if both the camera module and the flex cable is okay.


You may first check all the camera supply voltages from each corresponding DC to DC voltage regulator chips. IF both all supply voltages were stable, you may then check or try to replace the ESD/EMI filter chips.


There are two certain filter chips on the circuit, the one is for the main camera or camera 1 and the other one is for the second camera or camera 2.

N97 mini white, blue and blank screen display problem solution
A display problem like, white screen (WSOD), blue screen, blank or black screen, saturated and garbled screen displays, can be cause by a faulty or damaged LCD screen display and can be fix by installing anew LCD replacement on it. Sometimes an interrupted firmware also causes the problem and can be fix by restoring the device firmware. IF all of the above does not solved the problem you may then consider that the problem lies on the hardware components failures.

The solution below will show us a particular hardware components that holds and control the display data signals on Nokia N97 mini which enable the LCD screen to work.


The LCD display connector may also cause the problem if being corroded and oxidation occurs, cleaning it first is a good idea.


If the device suffered like wet damaged, accidentally heavily dropped the display controller IC and its particular line paths may also possibly damaged. Reworking and tracing each corresponding line tracks will help fix display problem on Nokia N97 mini.

Nokia N900 Solutions

vibrate



simcard

mic

memory card


light


keypad

earpice


chargeway



bluetooth

buzzer

samsung-i9000-galaxy-s-hard-reset

Please back up all of your personal data before you proceed. All data will be deleted on your Samsung I9000 Galaxy S by doing this procedure. However, this process will NOT delete data stored on the microSD memory card.

To Hard Reset Samsung I9000 Galaxy S

1. Turn the power off. If your Samsung Galaxy S is frozen, pull the battery out and reinsert it

2. Hold the Volume Down button

3. Press and release the Power button

4. You are now presented with a menu that allows for Fastbook, Recovery, Clear Storage, and Simlock

5. Select Clear Storage by pressing the Volume Down button

6. Press and release the Power button

7. Now simply confirm your decision: Volume Up for YES and Volume Down for NO

If YES is selected, all data including third-party applications will be deleted from your Samsung I9000 Galaxy S. Once the wipe is complete, the phone will reboot to its factory fresh state.

Activate iPhone without Official Carrier Sim; Fix Poor Battery Life Issue after Unlocking

Poor battery life was observed by iPhone users after they unlock their handsets using the combination of PwnageTool or Redsn0w to update baseband to 06.15.00 and Ultrasn0w 1.2 for iOS 4.2.1.


Be worry free since the developer of the application already figured out to fix the issue of poor battery life of unlocked iPhones. The developer recently released a jailbreak app called SAM (Subscriber Artificial Module). Even if you unlocked your iPhone with Ultrasn0w, it tricks your iPhone and iTunes into legitimate activation tickets.

Thanks to this wonderful application and you will get the full-blown benefits of the push applications and also addresses the poor battery life issue that you may encounter after unlocking your iPhone. The iPhone Dev Team said that developer @sbinger hit two birds with one stone.

You can follow these simple steps to install your jailbroken iPhone with SAM.

•Add http://repo.bingner.com as a repo in Cydia



•Install “SAM” and “SAMPrefs”


•Follow the steps in Troubleshooting/Hacktivated with redsn0w or PwnageTool


•Go to Settings > SAM and touch “De-Activate iPhone”


•Activate with iTunes


•If iTunes says invalid SIM, you will need to manually select the appropriate carrier under one of the methods besides “Automatic” and click on a SIMID
 
If you already hactivated your iPhone with PwnageTool or Redsn0w, then you can follow these easy steps to revert the handset into stock lockdownd.







•Option #1: redsn0w for iPhone 3G or 3GS on firmware 4.0 or later


1. Download redsn0w 0.9.6b6 or later from http://blog.iphone-dev.org.






2. Run redsn0w and select the “Deactivate” option.






•Option #2: my custom stockify program – works on any phone 3.0+


1. With SAM and SAMPrefs installed; install openssh and secure shell into your phone. Run “stockify” and it will revert your lockdownd to a stock lockdownd.






2. Reboot your phone.

Nokia X6 Some Solution

Nokia X6 Touch Screen Problem Solution


If ever trying to fix Nokia X6 touch screen failure issues and you'll do replacing the touch plate module, trying to calibrate the touch screen setting but unresponsive and restoring, upgrading and flashing the device firmware but nothing happens, the problem still exist and the touch screen left unresponsive.


This sometimes happens if the device suffered due to a wet damaged, heavily dropped and any related damaged accidentally done by the user. In this case only a hardware repair may only help solved the problem.

This solution below show the Nokia X6 PCB board components that holds and control the touch screen panel to work.

The solution above showed a Touch Accelerometer chip that used to sense orientation, detect direction in multi-access direction of the Touch Plate module. If the chip is damaged the touch screen will not work and remains unresponsive. This chip needs a DC supply voltage of 2.78 volts in this designed on Nokia X6 and also. The 2.78 Dc volts is also feeds and supply the touch plate module.


You may check this supply voltage first before trying to rework, re-ball or replacing the touch accelerometer chip.

Nokia X6 No Network Signal Reception problem solution - hardware repair
Here's the solution that may help and guide to repair Nokia X6 having a No Network Signal reception. If ever tried to restore and update the device firmware but nothing happens, this solution shows the corresponding RF circuit of Nokia X6 PCB board that might something wrong, faulty or being damaged.



Repair Tips:


1. Apply and supply voltage to the PCB board using desired DC regulated power supply voltage of 3.7 volts. Check the supply voltage from the cellphone's battery through to the corresponding components highlighted in red color, these are battery supply voltage filter coils that being feeds to RF circuit components. IF there are no voltage readings on that areas, check the continuity of the battery positive terminal on that certain parts. Apply jumper if the line is cut or open. check also the filter coils and replace if found damaged.

2. Check and measure the secondary voltage output from the RF DC to DC converter chip highlighted in orange color. If there is no voltage readings on that spots, rework or replace the DC to DC converter IC.

3. Check or replace the Clock crystal oscillator. (VCTXO)

4. Rework or replace RF Power Ampilifier IC (PA)

5. Rework or replace Front End Module IC (FEM)

6. Rework or replace Radio Frequency IC (RF IC)

X6 Send, E60 and END keypad keys failure solution


If the Send, E60 and End key button keys failed to respond on Nokia X6, and you already tried to restore, reset, flash and update the device firmware but nothing happens.


Keypad keys malfunction on Nokia X6 may also possibly caused by a faulty keypad flex, cleaning or by replacing it will help solved the problem.

If after replacing and ensuring that the flex is okay but the keys still unresponsive, you may then consider that the problem lies on a faulty keypad circuit's hardware components on the PCB board. This solution below will tell us which components holds and controls the keypad keys to function or work.


Check the keypad pin connector first ensure that it is free from dirt and oxidation.


From the keypad pin connector there are three line filter coils located near to it, have a check on this components and replace if found damaged.

From the keypad filter coils the lines is feeds to a keypad filtering chip or keypad IC, you may then check this chip, trace its line paths and replace if found damaged.

The I/0 Expander Chip is the keypad controller components, which holds and control the keypads including the Touch Control Module. You may also rework or replace this chip for further harder keypad problem repair on Nokia X6.


X6 Camera, Slider Lock, Volume Up and Volume Down Control Button Switches malfunction solution



Here's solution if something went wrong with Nokia X6 camera button and volume control switches that stop responding when being pressed. Button and switches may stop to function if being broken or damaged and sometimes cause by an oxidation. Simply by replacing it will fix the problem.


If the said button switch is okay seems working but still unresponsive you may then consider that the problem may lies on a faulty circuit components on the PCB board.

This solution below shows the line paths of each particular button switches of the camera, slider lock and the volume up and volume down buttons.

Nokia X6 Camera, Slider Lock, Volume Up and Volume Down Repair solution


Repair Hints:


Ensure that the button switches is perfectly clean and working okay.

There is an EMI-ESD filter IC is connected to each button switches line paths., Check this filter IC and trace the corresponding button switches line paths first before trying to replace it.

The Volume up control switch is connected directly to the I/O expander chip, you may check and rework this

chip if only the volume up is not working without touching the ESD filter IC.

Nokia X6 Camera Failure Problem Solution - hardware repair


Before using or applying this solution ensure to restore,flash and update,



the device firmware on Nokia X6. Oftentimes camera failure is cause by an interrupted firmware, restoring or flashing it back again will fix the problem. But


if that does not solved the problem you may then proceed to hardware repair troubleshooting, especially


if the device suffered from wet damaged and accidentaly dropped by the user.


The problem may possibly lies on faulty hardware components.

This solution below shows the main camera circuit on Nokia X6 and can be used as a guide to fix and repair camera hardware failure issues.


Camera Repair Tips:



a) Try to replace a new camera replacement module.


b) Check and clean the camera connector.


c) Do supply voltage measurement on corresponding camera supply voltages (see solution above). You can check this voltages while trying to enable the camera in ON condition.


There are three voltage converters circuit that feeds voltage to enable the camera. This voltage ranges are as follows, 1.8volts, 2.8volts and 1.3volts DC voltages.


This voltages are converted by a DC to DC converters chip. The chips converts the Battery voltage which is 3.7 volts and drop it down or minimize it to 1.8, 2.8 and 1.3 DC voltage.


So, ensure that the battery supply voltage is properly feeds to each of the DC converter chips.


If the battery supply voltage is present and still there is no voltage output you can read on each chip, you may then check or replace the DC to DC converter IC's.






d) If all voltages reading is working good and no problems found, but the problem still exists, you may then proceed to rework or replace the Camera Accelerator IC this chip holds and control the camera data signals before it feeds to the application processor IC.

Nokia X6 Bluetooth, WLAN and GPS solution - hardware repair






Bluetooth, Wireless LAN and GPS connection problem can be cause by a firmware failure and can be easily be fix by restoring, updating or flashing the phones firmware again. But after doing any firmware repair and the problem still exists the problem may certainly lies on the hardware components failures.

This solution below may possibly useful and help fix and repair Nokia X6 Bluetooth, WLAN and GPS problem issues for it shows the Bluetooh, WLAN and GPS component circuit.


Repair Hints: Ensure that the firmware of the device is successfully calibrated, upgraded and restored.



1) Check all corresponding supply voltages in the circuit


2) Check the RF buffer clock feeds from the RF circuit


3) Check the Bluetooth and WLAN antenna


4) Rework the Bluetooth IC first, the WLAN will not work if the Bluetooth IC is faulty.


Nokia X6 Insert Sim Card Problem Solution
Insert SIM card problem may happen and shows on the LCD screen display, if the SIM card inserted on the mobile phone device is already damaged but IF the SIM card card is working good and the device handset will not accept any kind of SIM card, the problem may lies on the device itself. This may happen if the mobile phone is damaged by a liquid or water damaged and any means of accidental damage by the standard user.

Here's solution that may help possibly help fix and repair Nokia X6 Insert SIM card problem.


This solution shows the SIM card circuit on Nokia X6, including The line tracks of the SIM card pin connector through to each corresponding solder ball bumps of the IC components (AVILMAS) that holds the SIM card to work.

Nokia X6 Ringer, Hands Free Speaker no audible sounds solution

This solution covers and may possibly help solved Nokia X6 Ringer and and Hands free loud speaker No sounds can be heard. You may need to ensure that the loud speakers is working well before applying this solution


 In Nokia X6 the handsfree speaker came with two channel the left and the right channel or so called stereo type. The audio signal is feeds from the power and audio chip (AVILMAS) and feeds to a audio amplifier IC to boost and amplify the sounds intensity.



You may need to check, trace, replace and rework those corresponding components indicated on the solution picture above.



Nokia X6 Digital Mic, mouthpiece microphone problem Solution



Here's the solution that might possibly help solve Nokia X6 mouthpiece microphone failure, a problem that no audio sounds can be heard from the other receiving device during a call is created.


The red lines indicated in the solution above is the microphone's supply voltage if this voltage is cut or not present the mic will not tend to work. There are also resistors that where the digital audio signal is flow across to this components that has a resistance value of 100ohms each, check and replace it first  before attempting to replace the Digital Microphone Module.

Nokia X6 Charger Not Supported Solution
Here's a solution that shows the location of BTEMP resistor that caused Charger Not supported on Nokia X6 if damaged. This components needs to replace if cahrger not supported shows on the LCD screen display when the battery charger is being plug-in.


























This Btemp resistor rated value is 47K. You may easily find it on other non working Nokia PCB board.

Nokia X6 Earpiece Speaker No Audio Sound Solution

if having tried to fix Nokia X6 Earpiece Speaker Problem that No Audio sound output can be heard and you already check speaker is okay and also already tried replacing the Flex cable wire but he problem unsolved. This solution might possibly help to solved the problem.

If the earpiece speaker and flex cable wire is working okay, those particular components highlighted on the solution might causes the problem if the device is severely damaged by any means of liquid or water damaged. Start to check on the flex pin connector and way down toall corresponding components composed of filter coil and bypass ESD resistor, replace at once if found open or shorted. If the filter coils were okay you may need to rework the power and audio IC (AVILMAS) trace the line paths first while the IC is being removed, then reball the IC, clean the solder balls surface and inplaced it back again.

Nokia X6 microUSB to PC connection, not detected problem Solution
If having problem connecting from USB to PC on Nokia X6, this solution may help if the device is not detected after ensuring that the USB cable wire is okay. The device driver is properly installed but the problem still exists.

This solution shows the particular components might caused faulty or damaged and result to a problem connecting to the PC through USB port.

Repair hints: Check the microUSB connector if damaged, oxidated or corroded, clean or replace it.


Check the filter coil and ESD protection chip, replace if found damaged. If the problem still persists check the power supply of the USB transceiver IC, it is conneted to the battery positive line voltage, if the voltage is okay, rework or reball the USB transceiver IC.

X6 LCD Display Problem Full Solution

Here's a solution that can be used to fix and repair Nokia X6 Display problem issues like white screen, blue screen, blank screen, garbled and saturated screen displays.. This solution may help if having a LCD display problems and already tried to upgrade or restore the device firmware and replaced it with a new LCD module replacements but the problem still exists.


There are two voltage supply that also need to the LCD display to work, the 1.8 volts and 2.78 volts.The solution above alao shows particular components that needs to check and replace if found faulty or damaged like the Display ESD-EMI filter IC.


If those supply voltages seems to be okay and the LCD display ESD-EMI filter IC is working well and already been checked and replaced the solution below shows the next components that also needs to check, rework or replace. On Nokia X6 there is a display controller IC that is being used and connected on the LCD display circuit.

If the LCD display controller chip become faulty or damaged this will also result to a display problem issues on Nokia X6. But before trying to reflow, rework or replaced you  need to check first the three filter coils connected near to it and trace each line paths to the LCD pin connector.

Apple Itunes restore error 1603 (iphone 2g, Iphone 3g, Iphone 3gs)

IF you get the Error 1603 while trying to restore, try the following:






Restart the Apple mobile service

Create a new User account in windows and try using that

Use a different USB port

Put the Iphone in DFU mode

Put the Iphone in Restore mode

If you have a sim card in the iphone.. take it out (It works sometimes)

Something as simple as restarting the computer and trying again might do it...

Allow the battery to fully discharge and recharger it and try again

Uninstall and reinstall itunes (try an older / newer version)

If you are determined enough.. using one or combination of the above methods does work..



it worked for me after approx 10 tries and me removing the simcard in the end..!!!

Blackberry activation required

How to remove ACTIVATION REQUIRED message
To remove the Activation Required, you need to get the 6-Digit MSL Code from Sprint. Then enter ##XXXXXX (where the 6Xs represent the MSL code). If the correct MSL code is entered, you will be taken to a screen where the top says, Mobile Directory Number. Change it to your 10 digit cell #, then press Menu, close and it will reset your fone & reboot and when the screen is back, you will see the name of your GSM provider and My Number will now show your cell number and you are good to go .

Get intallous to your iphone

Explanation and Solution on Nokia Bb5 Contact Service Problem Issues

How does Nokia Bb5 Contact Service Problem Occurs?




SX4: SX4 Smart Card, is a tool or method which is developed by Nokia to

write some data protection for a specific area in EEPROM is useful for

preventing modification of the data.





When SX4 PROCESS is Required ?



In the case of a loss (data corrupt) data charging (not charging), data

network (no network). Dll.RF calibration calibration-charging.

So, all these problems caused by mistakes in the process of flashing or after

write RPL or erase process is done in a certain area







HOW DO I KNOW THAT MY PHONE PROCESS SX4 needs to be done?



- When the phone appears CONTACT SERVICE, CONTACT retailers, NOT

charging after flashing, no network, etc. When the SELF TEST is done by

using the box like JAF repair, etc. will be obtained is the result of failed "ST_SECURITY_TEST Failed"



How do I make a SX4?





- Plug the phone in the repair box (JAF, MTBOX, MXKEY, etc.)

Write pm area with 309 results read from the normal mobile phone or can

also write FULL PM area without 308 (SIMLOCK area).





What to do sx4 without internet connection?





-sure Certificate damaged area musti made first with the FLASH erase, or

write RPL blank

Reset NPC (when using mxkey)

What is a Certificate Area?

Press info on the box like JAF flasher, etc. and see the results LOG ...

IMEI plain: 351862xxxxxxxxxx


IMEI spare to net: 3A 15 68 02 01 23 60 03

IMEI SV to net: 33 15 68 02 01 23 60 03 F6

LOCK STATUS:

Config KEY: 0000000000000000

Provider KEY: 2440700000000000

Provider: AT &T; U.S.A. (3650)

Key Code count: 0, FBUS Code count: 0

Block 1:Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN



Block 2: Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN





Block 3: Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN





Block 4: Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN





Block 5: Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN





Block 6: Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN





Block 7: Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock




This is an example of the correct Certificate

Default SN type:


Code:


IMEI plain: 123456765321?

LOCK STATUS:

Config KEY: fffffffffffffffffffffff

Provider KEY: fffffffffffffffffffff

Provider: Unknown

Key Code count: 0, FBUS Code count: 0



Block 1: Lock 1: CLOSED


BB5 Contact Service, Restart Problem,How To Erase BB5, Restore PM and RPL Backup!!!







I saw here many times peoples are having with this "Contact Service or Provider" problem

and also unable to Write or Restore the Orignal backup to the Phone. just follow and learned how to repair BB5 Contact Service/Retailer, how to erase BB5 and Restore PM and RPL Backup!!! Now we shall more reflect upon this matter;- How To Remove Contact Service or Provider ?

Firstly we should get Phone Info and see Imei and SL (Sim Lock) Zone are damaged or Not.Get Phone Info:

In Case when you got Damaged Imei: 123456789012345 and you dont have Orignal RPL Backup

then free way is try to solve this problem by downgrading if Imei and SP Data is still damage,

then Upgrade it back and you must need to buy an new RPL to fix this problem. Use ASK to RPL Service.

In Case when Phone Imei is oK but Only SL Zone is damaged and you don't have Orignal PM 308 backup then wat to do.If Courpted SP Data looks like this below:





CONFIG KEY: FFFFFFFFFFFFFFFF

PROVIDER KEY: FFFFFFFFFFFFFFFF

Provider: Unknown provider

And phone is supported for Unlocking, then you can try to Repair it free with any BB5 Unlocker by Unlock Button or with Repair SP Data Option. (It should Repair) Otherewise you may need to New RPL.



And If Courpted SP Data looks like this:

CONFIG KEY: 0000000000000000

PROVIDER KEY: 0000000000000000

Provider: Unknown provide

Then you must need to buy an New RPL whether Phone is supported with any BB5 Unlocker.

We can not Repair it free, Use Ask To Rpl Service.In Case when you have RPL Backup and have not PM 308, you can only Restore the Phone Imei but you can not Repair the Courpted SP Data like this: PROVIDER KEY: 0000000000000000,

Provider: Unknown provide In Case when you have PM 308 backup and have not RPL, you can Repair SP Data but you can not Repair Phone Imei by only PM 308 backup. Use ASK To RPL Service.

In Case when Phone Imei and SL Zone both are OK but phone is still on Contact



Service/Provider.

First take Self Test and check ST Security Test is Passed or Failed?

If Passed then do File System Formate and after that make Factory Setting and see problem is

solved or not, if still same then check phone hardware.

And if ST Security Test is Failed then Write PM Field [1] And [309] as stanner said,

(or full pm as you wish) by using SX4 Auth Service and after that make Factory Setting.

Oftenly Phone can Repair by Downgrading and Writing RPL.

Then Write PM With SX4 if same then Update back and See problem is Solved or not.

(It should work now!) otherwise try to repair it by erasing method.





How To Remove Restart Problem when Phone Imei is oK but Phone goes to Restart or Shut Off after a while!



In this case first try to solve this problem by only Write Full Modified (Without 308 Field) PM With

SX4 Auth.Use SX4 and when it done Successfully then immediately Write supported full modified PM to the phone and check phone without MMC, problem is fixed or not, if not then Full Flash and after that Write PM with SX4, or try to solve

by Downgrading.Oftenly Restart problem is removed by only do File System Format and Factory Default. (Check

phone without MMC) Otherwise there is only one way is left to Repair it with Software and that

is Erase Flash (Rap), to start the Erasing Procedure,



Follow this given below Method:



Before Start Erasing Flash, Save your both backup PM 308 and RPL backup (CRT 308 and CRT

BKP)If you are going to do erase newer BB5 + (Plus) Phone then you must Save also Full PM 0 to 400

Backup, coz you will need it for restore the orignal field 308, this is really fast easy and perfect

way to restore the PM 308 Field, otherwise you may need to buy an new RPL.So be careful. . .

Now we are ready to do erase.Select UNI_rapido.bin in Mcu Part and click to Flash

and for MT Select uni_rap.bin as MCU.

when phone will fully erased then Phone Imei will be: 12345610654321, SP Area will damaged

and CMT Flash Data will shown: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

Now Full flash with any Firmware ver but selected firmware should be not too Old or too New,

coz we may need it in another case.After Flash when phone will turn On, you will get

damaged IMEI: 12345610654321 and Courpted SP Area:

PROVIDER KEY: 0000000000000000, Provider: Unknown provide

Now first of all you have to Restore the Orignal backup of PM 308, in case when you are unable

to restore the PM 308 backup then flash again with same FW when you were take backup.

When it flash successfully then plz stay a min and write it (PM 308) back to the phone, now

Disconnect phone, connect it again and see SL Zone is Repaired or Not.

(It should be repair now), if not then flash again with same FW and restore the PM 308 backup.

But if you have Full PM 0-400 backup then no need to Flash again, just Write it (Full PM 0-400

backup) back to the phone without SX4,when it done successfully then remove cable to the box,

replug cable and get info you will see SP Area is Repaired now, if not then it will be repair after

writing RPL backup.

After successfully restore the PM 308 backup phone will on Contact Service/Retailers or full

working phone with damaged Imei. In this condition when phone has damaged Imei:

12345610654321 you can write full modified PM

(without 308 field) without using SX4, coz phone has not certificate (IMEI), therefor no need to

use SX4.Now we have to Restore RPL backup. If you are using JAF then Click on CRT Tool, now you will



See BB5 Certificate Tool Window:





tick on Write RPL Option and also mark on Plain RPL box, now Select your RPL backup and

click on Write RPL button.Get info now and see Imei is restored succcessfully or not phone

should be on Contact Service/Retailer or fully working. . .

But if you are failed to restore the RPL backup, i mean phone Imei is still damage and phone

show only Nokia and then shut Off in case now you Write blank_rpl and Flash again with Latest Firm Ware.

When it (flash process) done successfully then write RPL backup, get Info and see Imei is back or

not, it (Imei) should back now, and your Phone will on Contact Service/Retailer, if Not and you

got dead phone Please follow again all above erasing method.

Finally use SX4 and Write PM Field [1] and [309] (or full pm as you wish), now we have done all

abt Software.I think That's all. . . abt BB5 Repair with Erasing Method and we have confirmed

now, phone has Software Problem or not.

iPhone 2G, 3G and 3GS Passcode Remover Software Tools

This patch is already tested on iPhones: 3GS - 3G -2G OS 3.x and works 100%Note: your iPhones must be jailbroken and I repeat again that your iPhone must be AFC2 Support.



Download the patch from link below and extract it on your PC, Connect your iPhone with USB to your PC and make sure your iPhone is AFC2 support. (If your iPhone is Jailbroken with Redwn0w so dont care about AFC2)


Then open the iPhone Password Remover folder and just double click on M.H.M.bat !

a Dos windows will apear. after exiting the window restart your iPhone.

Now your iPhone is Passwordless
http://www.megaupload.com/?d=6UPAJ29P